2.1 Prepare a t program to be included in the configuration

// This script is intended to be used to check a configuration set as:
//
// [ ] Log everything
// [ ] FIFO mode
// Power settings: 5 Time to live after CAN power disconnected, in seconds
//
// CAN 1 should be connected to CAN 2
//
// Triggers:
// CAN1 Trigger1 Timer [4s] : Start logging, post-trigger=0
// CAN1 Trigger2 Timer [7s] : Stop logging, post-trigger=3000
//
// Script sends msg id:
// Id 1 at 0.5s
// Id 2 at 1.5s
// Id 3 at 2.5s
// Id 4 at 3.5s
// Id 5 at 4.5s
// ... and so on until
// Id 11 at 10.5s

variables {
  // Base channel. CAN messages will be sent on channel ch and received on
  // channel ch + 1
  const int ch = 0;

  // The singleshot timer is used to get a delay before the first CAN message
  // is sent.
  Timer singleshot;

  // The periodic timer is then used between each CAN message
  Timer periodic;

  // The message id of the sent CAN messages, will be incremented
  int msgId = 1;

  // The CAN message to be sent
  CanMessage msg;
}

on Timer singleshot {
  // Start the periodic timer to send 10 more CAN messages
  timerStart(periodic, 10);

  // After using the current CAN message id, increment before next use
  msg.id = msgId++;
  msg.flags = 0;
  msg.dlc = 8;
  msg.data = "\x12\x21\x13\x31\x22\x34\x41\x15";

  // Send CAN message
  canWrite(ch, msg);
  printf("Single shot MsgId: %d\n", msg.id);
}

on Timer periodic {
  // After using the current CAN message id, increment before next use
  msg.id = msgId++;

  // Send CAN message
  canWrite(ch, msg);
  printf("Periodic MsgId: %d\n", msg.id);
  if (!timerIsPending(periodic)) {
    printf("Timer done!");
  }
}

on start {
  printf("Starting testlogger companion script\n");

  // Setup the two CAN channels and go bus on.
  // This will override the settings in the binary configuration,
  // most notably the channels will no longer be in silent mode.
  canBusOff(ch);
  canBusOff(ch + 1);
  canSetBitrate(ch, canBITRATE_1M);
  canSetBitrate(ch + 1, canBITRATE_1M);
  canSetBusOutputControl(ch, canDRIVER_NORMAL);
  canSetBusOutputControl(ch + 1, canDRIVER_NORMAL);
  canBusOn(ch);
  canBusOn(ch + 1);

  singleshot.timeout = 500; // Wait half a second
  periodic.timeout = 1000; // One second period

  // Start the singleshot timer to send the first CAN message
  timerStart(singleshot);
  printf("Start periodic transmission\n");
}

on stop {
  printf("Stopping script\n");
  canBusOff(ch);
  canBusOff(ch + 1);
}

scc.exe
No input file found.
Script compiler for Kvaser t-script.
This is version 3.3.305 built on Sun Dec 13 19:38:53 2015.
Usage:
scc [-v -verbose] [-c] [-g] [-dx] [-devlines]
[-addsrc] [-comment=XXX]
[-pkey=N] [-skey=K]
@<filename>] [-dbase=<filename>] <filename>
where
-c Compile only. No output is produced.
-dbase=XXX.dbc Use the database XXX.dbc to define CAN messages
in the script.
-devlines Supress line numbers in generated code. Generates faster and
smaller code, but line numbers cannot be reported in exceptions.
-g Generate symbol tables for debug.
-addsrc Include the source code.
-comment=XXX Include the comment XXX.
Note that spaces can be used in arguments "like this".
Encryption of script and source code:
Script and source are protected by a symmetric crypto (-skey). The
symmetric key is then protected by a public key crypto (-pkey).
-pkey=N Use Kvaser public key number N.
Default:
0 - (no encryption) if no skey is entered
2 - (1024 bit RSA) if a skey is entered
-skey=K Use the symmetric key K.
If no K is entered and a pkey is, a random key K (hex)
will be generated for you
Key K formats:
-skey=0x11223344FFACAC - Hexadecimal format.
-skey=mysecretkey - ASCII format.
Contains multiple-precision arithmetic code originally written by
David Ireland, copyright (c) 2001-8 by D.I. Management Services Pty Limited
, and is used with permission.

scc.exe myCanGenerator.t -addsrc -comment="My CAN generator program v1.0"

2.2 Create a configuration

<?xml version="1.0" ?>
<!DOCTYPE KVASER>
<KVASER>
  <VERSION>2.0</VERSION>
  <BINARY_VERSION>6.0</BINARY_VERSION>
  <SETTINGS>
    <MODE fifo_mode="NO" log_all="NO"/>
    <CANPOWER timeout="5000"/>
  </SETTINGS>
  <CAN_BUS>
    <PARAMETERS bitrate="1000000" channel="0" silent="YES" sjw="1" tseg1="5" tseg2="2"/>
    <PARAMETERS bitrate="1000000" channel="1" silent="YES" sjw="1" tseg1="5" tseg2="2"/>
  </CAN_BUS>
  <TRIGGERBLOCK>
    <TRIGGERS>
      <TRIGGER_MSG_ID can_ext="NO" can_fd="NO" channel="0" msgid="3" msgid_min="3"
       name="trigger_0" protocol="NONE" timeout="0"/>
      <TRIGGER_MSG_ID can_ext="NO" can_fd="NO" channel="1" msgid="6" msgid_min="6"
       name="trigger_1" protocol="NONE" timeout="0"/>
      <TRIGGER_MSG_ID can_ext="NO" can_fd="NO" channel="1" msgid="3" msgid_min="3"
       name="trigger_2" protocol="NONE" timeout="0"/>
    </TRIGGERS>
    <STATEMENTS>
      <STATEMENT posttrigger="0" pretrigger="0">
        <EXPRESSION>trigger_0 OR trigger_2</EXPRESSION>
        <ACTIONS>
          <ACTION_START_LOG/>
        </ACTIONS>
      </STATEMENT>
      <STATEMENT posttrigger="2500" pretrigger="0">
        <EXPRESSION>trigger_1</EXPRESSION>
        <ACTIONS>
          <ACTION_STOP_LOG/>
        </ACTIONS>
      </STATEMENT>
    </STATEMENTS>
  </TRIGGERBLOCK>
  <SCRIPTS>
    <SCRIPT default_channel="0" primary="YES">
      <FILENAME>myCanGenerator.txe</FILENAME>
      <PATH></PATH>
    </SCRIPT>
  </SCRIPTS>
</KVASER>

2.3 Validating the configuration

import canlib.kvaMemoLibXml as kvaMemoLibXml

xl = kvaMemoLibXml.kvaMemoLibXml()
print("kvaMemoLibXml version: v" + xl.getVersion())

# Read in the XML configuration file
with open("config.xml", 'r') as myfile:
    config_xml = myfile.read()

# Validate the XML configuration
xl.kvaXmlValidate(config_xml)

# Get number of validation messages
(countErr, countWarn) = xl.xmlGetValidationStatusCount()
print("Errors: %d, Warnings: %d" % (countErr, countWarn))

# If we have any validation errors, print those
if countErr != 0:
    code = -1
    while code != 0:
        (code, text) = xl.xmlGetValidationError()
        print("%d: %s" % (code, text))

# If we have any validation warnings, print those
if countWarn != 0:
    code = -1
    while code != 0:
        (code, text) = xl.xmlGetValidationWarning()
        print("%d: %s" % (code, text))

# Exit if we had any validation errors or warnings
if countErr != 0 or countWarn != 0:
    raise Exception('Please fix validation Errors/Warnings.')

Footnotes

Getting started with kvmlib Part One

Digging deeper into kvmlib Part Three